Lapidary / Gemstone Community Forum
May 31, 2020, 05:47:50 pm
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
 
  Home Help Search Login Register  

rough too small to fit in vice

Pages: 1 [2]  All   Go Down
  Print  
Author Topic: rough too small to fit in vice  (Read 722 times)
deb193
Hero Member
*****
Offline Offline

Gender: Male
Posts: 2068


View Profile
« Reply #15 on: September 08, 2013, 03:02:38 pm »

No, those thin edge Lortone grabbers are crap. I gave all mine away.

The kind I showed photos of will work in both kinds. The square tube can be clamped form tob-bottom or front-back. Any local welding shop should be able to make one up.
Report Spam   Logged

- Daniel

(when everything is exceptional, nothing is)

peruano
Jr. Member
**
Offline Offline

Gender: Male
Posts: 88


Central New Mexico


View Profile
« Reply #16 on: September 16, 2013, 12:35:29 pm »

Vice devices are wonderful, but glue on a wood stub is "simple".  Don't be put off by drying time.  I've cut stuff within 6 hrs after gluing it up, but my standard is overnight to dry.  I use Gorilla Glue wood glue, but the standard Gorilla Glue works great too - just a bit harder to remove the glue and the wood stub.
Elmer'[s wood glue works as well - it may take a 3 day soak to get that last piece off the stub, but you have not wasted any rough, and you have not risked your blade to dubious holding accidents.  You need a semblance of a flat surface (trim saws rock) and then you have free reign.  Thanks for all the info on slab grabber like things.  I'm going to work on that route too.  Tom
Report Spam   Logged

Tom
Zoologist turned to Rocks
hulagrub
Hero Member
*****
Offline Offline

Gender: Male
Posts: 6748


When you cultivate man, you turn up all the clods


View Profile
« Reply #17 on: September 16, 2013, 03:25:01 pm »

Gorilla glue overnight! My home made slab grabber for geodes.
Report Spam   Logged

Dave, a certified Rockaholic

hardrockcafe
Guest
« Reply #18 on: September 25, 2013, 04:45:45 pm »

Daniel's design is a good one.

Here are three threads in another forum to give you some more ideas:

I made one like this:  http://andy321.proboards.com/thread/15517/cost-slab-grabber

http://andy321.proboards.com/thread/31966

I'm thinking about making one of these so I can cut Montana agate or others that require precise orienation:  http://andy321.proboards.com/thread/26058?page=2

Chuck
Report Spam   Logged
DadOhs
Full Member
***
Offline Offline

Posts: 126


Take me to your Labradorite!!


View Profile WWW
« Reply #19 on: September 25, 2013, 05:04:19 pm »

I use Elmers WoodGlue Max and a 4 inch long 2x4. glue and let sit overnight and you are good to go... I start from the inside edge and count the turns to the outside edge so I can plan my cuts and make the last cut to remove the stone from the board. no problems experienced to date!!

I bought the 8 oz bottle from Lowes and have had it for 3 months so far and still plenty to go b4 I need to buy more!!
Report Spam   Logged

Mario

Just when everyone thought I was finally gonna clean up my act, I found a new way to get muddy.

I once sought the meaning of life, but I got side tracked by an agate!
myrockpile
Newbie
*
Offline Offline

Posts: 32


View Profile
« Reply #20 on: September 28, 2013, 09:41:28 am »

If you have a flat face on the rock just super glue it to the end of a brick and you can be cutting in minutes for the price of a used brick. May sure you clean both surfaces first. I use a scrap piece of granite 2"x2"x4" but marble from home depot would work too.

Fred
Report Spam   Logged

RockIt2Me
Hero Member
*****
Offline Offline

Gender: Female
Posts: 680


"Rock It 2 Me!"


View Profile
« Reply #21 on: September 29, 2013, 03:03:32 pm »

I gorilla glue mine to a chunk of 2x4.
Report Spam   Logged

Nancie
"Rock It 2 Me"
Be kinder than necessary, for everyone you meet is fighting some kind of battle.   

 Don't take life so seriously...It's not like you're going to get out alive ;-)                                                        



hulagrub
Hero Member
*****
Offline Offline

Gender: Male
Posts: 6748


When you cultivate man, you turn up all the clods


View Profile
« Reply #22 on: September 29, 2013, 03:58:04 pm »

Nancie taught me this and it WORKS!
Report Spam   Logged

Dave, a certified Rockaholic

trigon
Jr. Member
**
Offline Offline

Gender: Male
Posts: 53


View Profile
« Reply #23 on: April 28, 2015, 09:59:17 am »

I've been using scrap wood for years with Elmers wood glue. It's worked fine. Since I got my new saw running, I've had nothing but trouble. Rocks coming off or slabs that won't cut evenly. I finally figured out that the saw is generating a lot of heat. The Elmers is getting rubbery and causing the stones to either rip off or shift.

Any ideas for a glue that will withstand higher temps?
Report Spam   Logged


Pages: 1 [2]  All   Go Up
  Print  
 
Jump to:  

Bookmark this site! | Upgrade This Forum
SMF For Free - Create your own Forum

Powered by SMF | SMF © 2016, Simple Machines
Privacy Policy